Category:
Series:
- Class D amp with Crown's ultra-efficient DriveCore technology weighs less than 11 lb
- Higher DSP capabilities: More control; has band pass filter per channel
- Increased lighting functionality; turn off all LED indicators except clip and thermal to reduce distraction in dark venues
- Selectable input sensitivity; 1.4Vrms and .775Vrms options so that amp can be driven at full power
- Set sleep mode after specified time without having to press a button
- Security setting disables menu buttons; menu locked/unlocked by entering combination
- System reset allows factory settings to be restored
- Remote power trigger
- Peakx™ Limiters provide maximum output while protecting your speakers
- XLR, 1/4", RCA inputs provide flexibility
- Integrated PureBand™ Crossover System for better performance and control
- Efficient forced-air fans prevent excessive thermal buildup
INV#182658
- Peak Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
INV#81757
- 8 inputs with 8 outputs
- Single rack space
- Balanced 3-pin Barrier block-type/line inputs
- 4-pin Phoenix-type speaker outputs
- Flexible input routing
- Multiple Power Confguration (Auto-Standby, Deep Sleep, and Green Mode)
- Auxiliary port for amp status and power saving mode (Deep Sleep)
- Circuit breaker protection with reset switch
- Convection-cooled chassis (no fan)
- Three-year, no-fault, fully transferable warranty that completely protects your investment and guarantees its specifcations
- Can be used in mass notifcation and EN 54 systems
- Patented technology including DriveCore TM
- Fault Reporting through Aux Port
- Adaptive Rail Technology for power on demand
- Complies with Green Edge by Harman
INV#81363
- Two-channel, 650W @ 4 Power Amplifier
- Class D amp with Crown's ultra-efficient DriveCore technology weighs less than 11 lb
- Higher DSP capabilities: More control; has band pass filter per channel
- Increased lighting functionality; turn off all LED indicators except clip and thermal to reduce distraction in dark venues
- Selectable input sensitivity; 1.4Vrms and .775Vrms options so that amp can be driven at full power
- Set sleep mode after specified time without having to press a button
- Security setting disables menu buttons; menu locked/unlocked by entering combination
- System reset allows factory settings to be restored
- Remote power trigger
- Peakx™ Limiters provide maximum output while protecting your speakers
- XLR, 1/4", RCA inputs provide flexibility
- Integrated PureBand™ Crossover System for better performance and control
- Efficient forced-air fans prevent excessive thermal buildup
INV#182659
- Peak Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
INV#81760
- Peak Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
INV#81759
- Extremely versatile; rated for 2-, 4-, 8-ohm loads and 70V and 140V outputs
- Switch-mode universal power supply
- Intuitive front-panel LCD screen for quick, easy configuration
- Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting
- Up to 20 user defined DSP presets are available
INV#40060
- 2 x 600 watts channels
- Low Z and 70 volt modes
- Analog amplifier
INV#158268
- XLC Amplifiers are compatible with CXM2000 for monitor, fault detection and crossover functions
- XLC Amplifiers are compatible with Crown Monitor System DSi-8M for monitor function
- Power for 2-ohm, 4-ohm and 8-ohm outputs, supporting stereo and bridge outputs
- Support parallel connection of cinema surround speaker
- Indicators provide accurate diagnostics: Power, Signal, Clip and Fault
- Volume control on rear panel of amplifiers
- High performance, light weight
- DriveCore based amplifier - weighs less than 14lbs (6 kgs)
INV#164389
- Peak Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
- 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
- Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
- New system monitoring provides software visibility of AC line voltage and power supply temperature
- Integrated cast-aluminum handles for easy handling and enhanced durability
- Locking power cord clip provides a secure connection between the amplifier and power cord
- Updated HiQnet System Architect™ control software
- Increased number of presets to a total of 50; 49 of which are user definable
INV#81758
- DriveCore Technology - Crown's proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design.
- Network Control and Monitoring - Through Harman's HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQ network.
- DSP - On-board Digital Signal Processor in each amplifier allows for custom configuration
- BLU link (BL models only) - Both receive and send channels over HARMAN's 256 channel, fault-tolerant audio BUS, BLU link
- Direct Drive 70/100Vrms Output - Each output channel is capable of provide either 70V or 100V for high impedance applications.
- Front-Panel Interface - Completely configure the amplifier using an intuitive front-panel interface.
- GPIO/AUX Port - Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.
INV#158271
- ANALOG & DIGITAL INPUTS - With digital audio transport via HARMAN's proprietary BLU-Link, plus balanced analog inputs, DCi gives you a tremendous audio advantage - at a much lower cost. The priority input router allows you to specify a primary input, and if audio is lost the amp automatically switches to the other input.
- NETWORK MONITORING & CONTROL - Better monitoring, control and audio manipulation with the HiQnetâ ¢ protocol that's over standard TCP/IP. Remotely see how all networked DCi amplifiers are performing and control them as needed. In addition, this allows Audio Architect software and the Powered by Crown app to work with DCi amplifiers.
- PROGRAMMABLE GENERAL PURPOSE INPUT/OUTPUT PORTS - GPIO ports can be configured in many different ways, such as volume controls, recall presets, or to report errors to a master computer.
- "DIGITAL SIGNAL PROCESSING - DSP capabilities include the following: LevelMAX Limiters Input/Output EQ Crossover Delay Matrix Mixer Speaker Line Monitoring
INV#180450
- 4 inputs with 4 outputs
- Single rack space
- Balanced 3-pin Barrier block-type/line inputs
- 4-pin Phoenix-type speaker outputs
- Flexible input routing
- Multiple Power Confguration (Auto-Standby, Deep Sleep, and Green Mode)
- Auxiliary port for amp status and power saving mode (Deep Sleep)
- Circuit breaker protection with reset switch
- Convection-cooled chassis (no fan)
- Three-year, no-fault, fully transferable warranty that completely protects your investment and guarantees its specifcations
- Can be used in mass notifcation and EN 54 systems
- Patented technology including DriveCore TM
- Fault Reporting through Aux Port
- Adaptive Rail Technology for power on demand
- Complies with Green Edge by Harman
INV#81361
- Extremely versatile; rated for 2-, 4-, 8-ohm loads and 70V and 140V outputs
- Switch-mode universal power supply
- Intuitive front-panel LCD screen for quick, easy configuration
- Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting
- Up to 20 user defined DSP presets are available
INV#40573
- Patented 5th-generation Class-I circuitry provides terrific efficiency for strong performance with a low power draw
- Built-in BSS OmniDrive HD DSP processing and 24-bit/192kHz Cirrus Logic SHARC converters, along with FIR and IIR filters provide ultra-smooth performance
- A front-panel USB connector lets you connect a USB drive to quickly transfer DSP settings that were created in a computer
- Analog XLR inputs and outputs, as well as AES/EBU digital XLR inputs and outputs. Speakon and Binding Post outputs are also provided
- An Ethernet port supports TCP/IQ, HiQnet, and CobraNet, and is compatible with standard 100Mb Ethernet hardware
- Front-to-rear cooling fans have true tachometer feedback for precision control of thermal performance
- Sweep Load Monitoring (SLM) technology provides system-level diagnostics
- Global power supply
INV#58281
- The Crown®Macro-Tech®i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
- Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
- Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
- Global Power Supply—designed to deliver maximum power no matter what country you work in
- Built-in load, line voltage, input and output monitoring
- Standard Ethernet networking via System Architect®lets system operators monitor and control the amplifier from any location
INV#51366
- The Crown®Macro-Tech®i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
- Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
- Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
- Global Power Supply—designed to deliver maximum power no matter what country you work in
- Built-in load, line voltage, input and output monitoring
- Standard Ethernet networking via System Architect®lets system operators monitor and control the amplifier from any location
INV#51365
- The Crown®Macro-Tech®i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
- Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
- Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
- Global Power Supply—designed to deliver maximum power no matter what country you work in
- Built-in load, line voltage, input and output monitoring
- Standard Ethernet networking via System Architect®lets system operators monitor and control the amplifier from any location
INV#51363
- 8 x 300 watts channels
- Low Z and 70 volt modes
- Includes advanced DSP + HiQ Net control
INV#158263
- Patented 5th-generation Class-I circuitry provides terrific efficiency for strong performance with a low power draw
- Built-in BSS OmniDrive HD DSP processing and 24-bit/192kHz Cirrus Logic SHARC converters, along with FIR and IIR filters provide ultra-smooth performance
- A front-panel USB connector lets you connect a USB drive to quickly transfer DSP settings that were created in a computer
- Analog XLR inputs and outputs, as well as AES/EBU digital XLR inputs and outputs. Speakon and Binding Post outputs are also provided
- An Ethernet port supports TCP/IQ, HiQnet, and CobraNet, and is compatible with standard 100Mb Ethernet hardware
- Front-to-rear cooling fans have true tachometer feedback for precision control of thermal performance
- Sweep Load Monitoring (SLM) technology provides system-level diagnostics
- Global power supply
INV#58282
- 2U -4 ch x 1900watts at 8ohm, 3500watts at 4ohm,
- Built in Crown OmniDriveHD DSP, touring amp,
- SpeakOn out
INV#119196
