Category:
Series:

- Wood clapper
- Compatible with a variety of dry erase markers
- Affordably priced, compared to most similar slates
INV#252815

- Up to 1000ft full-duplex wireless communication
- Rechargeable beltpacks run up to 8 hours on a full charge
- 1 base station connects to 4 beltpacks
- Built-in noise reduction headsets
- Base station can be powered either by L series style batteries or AC wall plug (Single fully charged NP-F970 battery last up to 20 hours)
- Expandable to an additional base station to total 8 beltpacks (additional unit sold separately)
- Uses 1.9GHz frequency band
INV#253398

- 95 CRI LEDs
- Solid 5600K Color Temperature
- Bright Consistent Light
- Beam Angle of 50 degrees
- DMX512 In and Out
- Baby 5/8 inch/Junior 1-1/8 Combo Pin adaptor with right angle receiver hole
- 30 degree angled yoke for unobstructed movement
- Stronger steel tension knobs for locking the light into place
- Single knob control for adjusting color,brightness, or DMX
- New LED Readout screen giving you precise adjustments
- Watts equivalent to 400 watts incandescent light
INV#253188

- 2 Risers, 3 sections
- Max height: 95" (241.3cm)
- Min height: 38.5" (97.79cm)
- Closed height: 36" (91.44cm)
- Weight support: 8lbs. (4kgs.)
- Air cushioned risers
- 5/8" pin mounting point
INV#253003

- Padded Anti-Slip Surface
- Accepts any Accessory with a 1/4-20 Mount
- Receives any 5/8" Stand or Adaptor
- Can Support Up To 5 lb.
- Solid Metal Construction
INV#253288

- Dual Sony “L” Series Battery Charger
- Can charges two batteries simultaneously
- 2 – 5800 mAh batteries
- Replacement for the NP-F750 L-Series Battery
- Compatible with the iLED144, ilED312(-v2), ID508, IB508, iLED6
INV#253068

- 95 CRI Chip LEDs paired with 1/2 stop soft diffusion panel
- Bi-Color adjustable from 3200K-5600K
- Bright consistent light across all color temperatures
- Beam Angle of Soft panel 110 degrees
- A clean single shadow without the artifacts
- Baby 5/8 inch/Junior 1-1/8 Combo Pin adaptor with right angle receiver hole
- 30 degree angled yoke for unobstructed movement
- Stronger steel tension knobs for locking the light into place
- Single knob control for adjusting color or brightness
- New LED Readout screen giving you precise adjustments
- AB mount or V-mount battery plates included
- Included bard doors with intensifiers
- Watts equivalent to 850 watts incandescent soft light
- RF Remote Control allows you to turn on and off the light
INV#253095

- 95 CRI LEDs
- 3200K – 5600K Color Temperature
- Bright Consistent Light
- Beam Angle of 50 degrees
- Baby 5/8 inch / Junior 1-1/8 Combo Pin adapter with right angle receiver hole
- Stronger steel tension knobs for locking the light into place
- Single knob control for adjusting color, brightness
- New LED Readout screen giving you precise adjustments
- Battery powered by Sony “L” series style batteries
- Included barn doors with intensifiers
- Watts equivalent to 550 watt incandescent light
INV#253164

- 1000 nit high bright monitor
- High-quality American made 70/30 beam splitter glass
- Screen readable from up to 20'
- Multiple camera mounting options
- Easy balancing with adjustable base
- Lightweight and compact design
- Monitor supports image flip
- PrompterPro software for MAC & PC is FREE with this teleprompter
- 3G-SDI, HDMI, and VGA
INV#253368

- 95 CRI 98 TLCI
- Daylight 5600K
- IP54 rain and dust-proof
- Rugged aluminum construction
- Fanless passive cooling design
- 5" Fresnel with spot 28Deg to flood 53Deg
- Bright consistent color temperature
- V-Mount battery adapter included
- Barn doors and gel frame included
INV#253425

- Braided Steel Cable
- Quick Attaching Lock
- Easily Secures Light to Grid
- 4.5mm Diameter
INV#252809

- Braided Steel Cable
- Quick Attaching Lock
- Easily Secures Light to Grid
- 2mm Diameter
INV#253196

- Attach V-Mount Battery to Light Stands or Gimbals
- Convenient Way to Power Lights/Monitors
- Supports Up To 3 Pound Batteries
INV#253413

- 4x D-Tap Output connections
- 1x 5V USB Output connection
- Use longer-lasting V-mount batteries with your DSLR or other devices
- Mounts onto a pair of industry-standard 15mm LWS rods
- Can be mounted to the back of the rig as a counterweight
INV#253405

- Allows you to connect an external monitor to your camera rig
- Includes two NATO rails
- 11 lbs. max payload
- Freely adjustable tilt with adjustable tension
- Compatible with monitors 1/4-20 mounted monitors
- Includes ARRI location pins for a more sturdy mounting solution
- 180Deg tilt and 360Deg swivel adjustment
INV#253426

- Quick and Easy Basic Lens Support
- 7/8" of Vertical Adjustment
- Slide-On or Slip-On Installation: One Open Rod Mount Gives More Placement Options
- Solid Aluminum Construction Cuts Weight and Increases Durability
INV#253309

- Solid Aluminum Follow Focus with Adjustable Hard Stops
- Horizontally Positionable
- Includes Magnetic Marking Disc for Hand Wheel
- Mounts to 15mm Rods
- Installed .8 Pitch Lens Gear
- Includes .8 Pitch Zip Gear
- Slide-On or Slip-On Installation: One Open Rod Mount Gives More Placement Options
INV#253311

- Complete Shoulder Mount Rig System for Canon C200 & C200B
- Includes Two Handgrips
- Includes Two Carbon fiber 15mm rods
- Includes Canon Hand Grip Relocator Cable
- Includes Rotatable Monitor/EVF mount
- Shoulder Pad Features Manfrotto 501 Mount
- Compatible with Monitors up to 7 inches
- Compatible with any Arri Rosette Mounted EVF
INV#253416

- Form-Fitted to the Blackmagic Pocket Cinema Camera 6K and 4K
- Arca-Swiss Plate Mounts to Cage Base and Many Photo Tripods
- Top Handle Mounts Directly to NATO Rail/Top Rod Mount
- Top Handle can Accept 15mm Rod to Expand Accessorizing Options
- Cut-Outs for Battery, Memory Card, and A/V Output Access
- Mounts to Tripod Quick Release Plate with 1/4-20 and 3/8-16 Mounts on Base Bottom
- Mounts to ARRI Standard 19mm Dovetails
INV#253391

- Double ball-joint magic arm with 1/4-20 screw and ARRI location pins
- For mounting accessories to your camera cage
- Anti-skid rubber rings increase the friction of each of ball head
- Ball joints allow you to position accessories freely
- Includes two 1/4" to 3/8" thread adapters
- 1/4"- 20 threads to mount other accessories
- Made of aluminum alloy
INV#253427

- Form-Fitted to the Sony a7R IV & III Series Cameras
- Fits Sony a7 III, a7S II, and a7R III
- Arca-Swiss Plate Mounts to Cage Base and Many Photo Tripods
- Top Handle Mounts Directly to Cage Front
- Top Handle fits Ikan Grips and Many Bicycle Handles for Custom Grip Mounting
- Top Handle can Accept 15mm Rod to Expand Accessorizing Options
- Cut-Outs for Battery, Memory Card, and A/V Output Access
- Mounts to Tripod Quick Release Plate with 1/4-20 and 3/8-16 Mounts on Base Bottom
- 15mm Rods are Vertically Positionable to Support Multiple Lenses and Accessories
INV#253397

- Form-Fitted to the Sony a7 III Series Cameras
- Fits Sony a7 III, and a7R III
- Arca-Swiss Plate Mounts to Cage Base and Many Photo Tripods
- Top Handle Mounts Directly to Cage Front
- Top Handle fits Ikan Grips and Many Bicycle Handles for Custom Grip Mounting
- Top Handle can Accept 15mm Rod to Expand Accessorizing Options
- Cut-Outs for Battery, Memory Card, and A/V Output Access
- Mounts to Tripod Quick Release Plate with 1/4-20 and 3/8-16 Mounts on Base Bottom
- 15mm Rods are Vertically Positionable to Support Multiple Lenses and Accessories
INV#253312

- Form-Fitted to the Sony a7 II Series Cameras
- Fits Sony a7 II, a7S II, and a7R II
- Arca-Swiss Plate Mounts to Cage Base and Many Photo Tripods
- True NATO Top Handle Mount
- Top Handle fits Ikan Grips and Many Bicycle Handles for Custom Grip Mounting
- Top Handle can Accept 15mm Rod to Expand Accessorizing Options
- Cut-Outs for Battery, Memory Card, and A/V Output Access
- Mounts to Tripod Quick Release Plate with 1/4-20 and 3/8-16 Mounts on Base Bottom
- 15mm Rods are Vertically Positionable to support multiple lenses and accessories
INV#253313

- Form-Fitted to the Sony a6500 and a6400 Camera Body
- Fits Sony a6000 and a6300
- Arca-Swiss Plate Mounts to Cage Base and Many Photo Tripods
- True NATO Top Handle Mount
- Top Handle fits Ikan Grips and Many Bicycle Handles for Custom Grip Mounting
- Top Handle can Accept 15mm Rod to Expand Accessorizing Options
- Cut-Outs for Battery, Memory Card, and A/V Output Access
- Mounts to Tripod Quick Release Plate with 1/4-20 and 3/8-16 Mounts on Base Bottom
INV#253314